So, after applying RSMB, make sure to click on "Use 'Motion Src' track in the RSMB settings, and in addition make sure to drag the media you want to use for the Motion Src to the Motion Src track in the timeline (even if it's the same clip that RSMB is applied to). Note to Boris Red Users: Because of the way Borid Red works, you must specify the motion source clip manually (even if the motion source and the color source are the same clip). If an alternate motion clip is supplied, then it must have the same pixel dimensions as the color source otherwise a semi-transparent red image will be produced to let you know that there is an error. Of course, RSMB assumes that both the Motion Source and clip that RSMB is applied line up exactly in time. However, if an Motion Src clip is specified, then this sequence is used for tracking and the color is retrieved from the clip that RSMB is applied to. If Motion Src is set to "None" then the source that RSMB is applied to is used for both tracking and the color of the RSMB sequence. For these reasons we allow you to change the source that is used for tracking purposes.
![reelsmart motion blur after effects tutorial reelsmart motion blur after effects tutorial](https://cgpress.org/wp-content/uploads/2015/03/RSMB.jpg)
Or, the reverse, you might have heavily filtered the original, but you think you might get better tracking results by using the original footage as the imagery to be tracked. On some sequences you might say to yourself, "if only I could enhance the colors used in the tracking process, but then use the colors from the original sequence for the motion blurred sequence." For example, the tracking of RSMB does not work particularly well on a low contrast or dark sequence.
![reelsmart motion blur after effects tutorial reelsmart motion blur after effects tutorial](https://i.ytimg.com/vi/GzqcczBx3JM/maxresdefault.jpg)
TIP: When the sequence being processed has a cut or dissolve embedded, you may want to reduce the motion blur amount (or even set it to zero) during the transition.īy default a layer's own motion is used to blur the layer. Keep in mind that RSMB may not be very effective at removing motion blur in imagery that has large amounts of motion blur. To remove motion blur, provide a negative amount of blur. The default amount of 0.5 corresponds to 180 degree camera shutter opening. Of course you may add in as much or as little as desired. 1 means blur the "standard" amount (blur using the direction and amount of motion found).
![reelsmart motion blur after effects tutorial reelsmart motion blur after effects tutorial](https://getintopc.com/wp-content/uploads/2019/04/ReelSmart-Motion-Blur-Pro-Plugin-Direct-Link-Download-GetintoPC.com_-300x182.jpg)
This is useful to know when trying to figure out why RSMB doesn't apply blur to frames from a 3:2 pulldown sequence or animation done on "2"s, etc. The plug-in calculates the motion between two successive frames in a sequence, calculates the motion from one frame to the next, and applies blur based on the calculated motion. ReelSmart Motion Blur supports 8 and 16 bits per pixel processing and floating point is supported for After Effects 7.0 and later. To find out more about RE:Vision Effects and our product lines, visit our website at.
![reelsmart motion blur after effects tutorial reelsmart motion blur after effects tutorial](https://support.chaos.com/hc/article_attachments/4409417705745/max_velocity_in_last_frame.png)
You can even can blur one sequence by using the motion from another for very interesting effects. Of course you can add as little or as much blurring as you need, and even remove some motion blur. Our tracking technology is at the heart of ReelSmart Motion Blur, so there is no handwork involved. In particular we support:Īutomatically add more natural-looking motion blur to a sequence using ReelSmart Motion Blur. Go to the "ReelSmart Motion Blur" section and navigate to the tutorials page. NOTE: We have tutorial projects for common ReelSmart Motion Blur uses.